A：Instructions For Use Of Heat Shrink Packaging Machine
Q：1. Before starting, check whether there is foreign matter in the heat-shrinking channel, and remove any foreign matter; the oil level of the reducer should be between the upper and lower lines of the observation glass, and there is no enough increase. Turn on the main power switch, and turn on the starting power switch, and the green indicator light is on.

2. Move the operation switch to the "ON" position, start the operation, and observe whether the Hengji chain is stuck with abnormal noise.
3. Adjustment of heating temperature
3.1. Rotate the temperature control knob clockwise to control the upper temperature at the temperature required for shrinkage.
3.2 Rotate the lower heating knob clockwise to control the heating temperature at the required shrinkage temperature (generally the upper temperature is 120~180℃, and the lower temperature is 120~160℃).
3.3 Turn the fan switch clockwise to the ON position, the fan runs normally.
4. Downtime
When shutting down, first turn off the upper and lower heating and temperature control power supply. After the temperature of the heat shrinking machine has been running for 5 minutes, turn off the running switch to the "OFF" position, and the heat shrinking machine will stop running; turn off the fan switch, turn off the starting power switch, and turn off the main power switch. , the machine is cleaned, and the shutdown is completed.
5. Maintenance and Repair
5.1 Check and maintain the machine once a month before use. The contents include: add a little grease to the chain, replace the braided tube if it is damaged, and check and test the heating part and running part of the control power supply to ensure the normal operation of the machine.
5.2 Check the electrical part once a month.
5.3 Repair once every year of use.

A：Heat Shrink Film Packaging Machine Temperature Adjustment
Q：It is recommended to debug directly on site, the effect is better. Theoretically, the shrinking temperature of POF film is about 110-130 degrees Celsius, the shrinking temperature of PVC is about 130-160 degrees Celsius, and the temperature of PE shrinking film is about 140-170 degrees Celsius.
Moreover, the installation position of the thermocouple is different. For the same shrinkable film, the temperature control meter can show that the shrinkage is not good at 200°, and some temperature control meters show that the shrinkage effect is very good at 100°.
In addition, for the same packaging machine, due to the different quality of the shrink film, there will also be a large deviation in the thermal shrinkage temperature.

A：Precautions For Cigarette Charter Machines​​​​​​​
Q：1. Regularly check the sensor and cylinder drive assembly, it should confirm whether the cylinder is flexible, and ensure that the sensor is always on the same plane and on the same line. If the accuracy of the sensor is found to be poor, inflexible, etc., the sensor needs to be repaired or replaced in time.
2. Regularly check the transparent film packaging machine (cigarette packaging machine) equipment, once a month, keep the room clean and tidy, and do not let the acid and other corrosive gases contained in the atmosphere flow. When the three-dimensional transparent film packaging machine is found to be corroded, it should be repaired at any time. Don't let the 3D automatic packaging machine work again. The entire machine must be kept clean and tidy and oiled to prevent rust, and covered with a cloth when not in use.
3. Be sure to carefully check the joints of the three-dimensional cigarette packer to ensure that the joints are firmly connected and the parts are in good use. If there is any abnormal situation, please stop working immediately and cut off the power, and promptly notify the maintenance personnel to come to check and repair.
4. When the transparent film three-dimensional packaging machine is not used for a long time, the measuring barrel and sensor should be removed and protected in time; the exposed part of the piston rod of each cylinder should also be coated with butter to prevent rust stains.
5. When the transparent film three-dimensional packaging machine system automatically runs in the default mode, it will automatically detect and confirm whether all the cylinders are in the reset state. If it's not in reset, the system will alarm and everything will be reset. When the system switches from the automatic operation state to the manual operation state or switches between the two states, all cylinders are reset automatically (i.e. tilting, pushing, forming, easy pulling, folding, folding, cutting and blowing are all reset to the initial state) .
6. Regularly clean and clean the transparent film three-dimensional packaging machine to make its appearance clean and tidy, and prevent external dust and debris from entering the inside of the machine through the feeding port, causing pollution to the packaged items.

A：Operation Process Of Transparent Film Three-dimensional Packaging Machine
Q：1. Preparations before the operation of the cigarette packer
(1) Due to the bumps and vibrations of long-distance transportation, the following strict inspections must be done before operation:
a. Open the rear cover, observe the electrical box, check the electrical wiring, whether the components are off, and whether they are fastened;
b. Check whether the mechanical fasteners are loose, fall off, and whether the parts are displaced.
(2) Power transmission test: Turn on the power supply, and check the rotation of the motor after connecting the wires (looking from the outside to the body) - it should be clockwise.
2. Basic operation of the cigarette packer
(1) Turn on the power switch of the cigarette packer, and the power indicator light is on.
(2) Open the long interface seal A. Inside seal B. Upper shaping C. Long interface seal D. Outside seal E. Lower shaping F. Thermostat, adjust the temperature to about 110℃.
(3) Feeding: Manually put a certain amount of packaged products in the stocker, and make a certain amount of packaged products on the conveyor belt.
(4) Adjust the inverter so that the machine starts to work from slow to fast.
(5) Shutdown: turn off the power, clean the workbench and various parts.

A：The Use Principle Of Automatic Transparent Film Three-dimensional Packaging Machine
Q：1. The three-dimensional automatic packaging machine is easy to operate. It adopts PLC control and is equipped with a touch screen man-machine interface control system, which is easy to operate.
2. Frequency conversion speed regulation, the machine uses frequency conversion speed regulation device, and the speed can be adjusted at will within the specified range.
3. Automatic detection function, if the bag is not opened or the bag is incomplete, no material is added, no heat sealing, the bag can be reused, and no material is wasted, saving the production cost for the user.
4. The protection device will alarm when the working air pressure is abnormal or the heating tube is faulty.
5. Horizontal bag feeding method, the bag holder can store more bags, lower requirements for bag quality, high rate of bag separation and bag loading
6. The adjustment of the bag width is controlled by motor. Press and hold the control button to adjust the width of each group of clamps at the same time, which is easy to operate and saves time.
7. Some imported engineering plastic bearings are used, no need to refuel and reduce the pollution to materials;
8. The products packaged by the cigarette charter machine are beautiful, which is in line with the minimalist aesthetics of today's young people.